Is There A Spray On Guitar Case Cover Repair?
QualSpray™ is our exclusive line of spray guns, pressure level pots and accessories imported directly by Homestead. Nigh of these products are designed or configured to our specifications. All products are pre-tested here earlier they're shipped out and they come complete with supplemental instructions written by u.s. to get you up and running or for time to come troubleshooting.
QualSpray Spray Guns
The almost mutual question nosotros're asked is "How do I choose a gun"? Generally you can make your pick based upon your compressor size, the materials you want to spray and the type of projects.
Compressor size – your compressor should accept a CFM (or SCFM) specification of how much air it can produce. This is stated in the manual, or most of the fourth dimension on a plate on the compressor. Compressors unremarkably give 2 ratings, one figure at 90psi or higher and another at 40 psi. The i you should use for spray equipment is the 40 psi one. That number should be equal to or slightly higher than the CFM measurement of the spray gun.
Materials y'all want to spray – are you spraying woodworking or automotive finishes. Primarily waterbased or solvent based? Do you want to exist able to spray paints (latex and oil)?
Type of projects – are you doing architectural spraying or spraying furniture. Practice yous primarily do kitchen cabinets? Do you spray the aforementioned textile all the time or are y'all constantly changing from stain/dye to sealer then clears.
TYPES OF SPRAY GUNS
HVLP/LVLP Guns – are a hybrid of HVLP, besides called Low-Cfm. To allow folks that have smaller compressors (under 8 cfm at 40 psi) engineers designed a special blazon of HVLP called LVLP (Low Volume/Depression Pressure). In LVLP guns, the atomizing ports in the aircap horns and around the center hole are much smaller (see photograph beneath). These smaller holes accelerate the lower air supply of the compressor to break up the end. LVLP guns have a very soft spray pattern like HVLP but are not equally fast (usually not an issue unless you lot practise production work). LVLP guns are very good at detail work, small project piece of work, and finishing at home (very soft spray and low overspray) QualSpray LVLP guns are the QS-125WB, QS-600WB, AM-6008LVLP and the AM-5008 series.
RP Guns – RP stand for reduced pressure. In that location are too called High Transfer Efficiency (HTE) guns. A reduced force per unit area gun operates in a similar manner to a conventional loftier pressure gun just a reduced inlet pressure of 35 psi. The air caps are engineered in a way to operate at a tip pressure higher than ten psi (the mandated limit for HVLP) but at a lower air inlet force per unit area setting than a conventional spray gun. They still deliver transfer efficiency of 65% or greater. Reduced pressure guns are finding favor amongst finishers who adopt old way high pressure level guns and didn't like the lower tip pressure (softer sprays) and slower delivery rates of HVLP and LVLP. Reduced pressure guns volition atomize articulate finishes the best and can provide faster delivery rates of finish. I nice quality of our RP guns is that you tin operate the gun at a lower pressure level like twenty-25 and get 7 or viii psi tip pressure like an HVLP/LVLP gun! Our Reduced pressure guns likewise require modest compressors, just like the LVLP guns. QualSpray RP guns are the AM-2012RP series.
AM-2012RP SERIES REDUCED PRESSURE GUNS
New for 2022! AM-2012RP "Reduced Pressure" – Want a gravity gun that will spray finishes like the one-time style high pressure guns but with the transfer efficiency of HVLP? This technique is known as Reduced Pressure. This gun utilizes a gun inlet pressure of around 35psi to atomize and lay down clears beautifully but at a transfer efficiency of 67%. The package we put together works for both automotive or woodworking and will spray the most popular finishes with small compressors (only 6 cfm required) Gun incorporates stainless steel in the fluid passages, threaded connector to the cup, nozzle and needle. This upgrade past our manufactory insures proper functioning with waterborne finishes and catalyzed solvent products. Optional aluminum cup for those that prefer one.
For PPS utilize the #26003 PPS adpater #S2c
ii Year WARRANTY
Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets/seals: Teflon
Cups: 600cc nylon or aluminum (other sizes available)
Working Pressure : 35 psi (at gun inlet)
Air Consumption: vi cfm
Needle/nozzle/air cap: included in kit, ane.4mm, ane.8mm, ii.0mm
| MODEL | Description | Buy NOW | PRICE |
| #AM-2012RPN | Gun with 600cc nylon cup, regulator, 1.4mm, two.0mm, one.8mm NN setups, repair kit, strainers, service wrench. Requires six CFM | $325.00 | |
| #AM-2012RPA – half-dozen CFM OR College | Gun with 600cc ALUMINUM cup, 1.4mm, ane.8mm NN setups, repair kit, strainers, service wrench. Requires vi CFM | $325.00 | |
ACCESSORIES & REPLACEMENT PARTS
#HW-SS-3G – three pack replacement stainless steel strainers – $7.50
#AM-2012/125NYC – 125cc nylon cup – $25.00
#AM-2012/200ALC – 200cc aluminum cup – $28.00
#AM-2012/400ALC – 400cc aluminum loving cup – $28.00
#AM-2012/600NYC – 600cc nylon cup – $30.00
#AM-2012/600ALC – 600cc aluminum cup – $32.00
REPLACEMENT NEEDLE/NOZZLE/AIRCAP SETS
#AM-2012/20 – 2.0mm NN kit for AM-5008 – $64.95
QS Serial HVLP GRAVITY DETAIL/TOUCH Up GUN
QS-125WB – This is my go-to gun for applying sunbursts and touch-ups. It can also do articulate-coats but will be a scrap slower than a total size gun such equally the AM-2012RP or AM-5008. If you have a small pancake manner compressor or ane that has 4 cfm or then this is the gun to go. The 1.5mm will spray articulate finishes without thinning unless they are pretty thick. The 125cc cup volition hold near 4 ounces of finish, only larger cups are available every bit an optional upgrade if you need information technology. Spray Gun comes with a two year warranty.
Go the PPS #21 adapter for use with this gun.
– $319.00 (Includes 0.viii, 1.2 & one.5mm setups, regulator, repair kit, all in a plastic case see below)
Note: Non-US Customers please buy this product hither so proper customs/duties/shipping rates can be calculated through the eBay Global Shipping Program.
| MODEL | DESCRIPTION | Buy NOW | PRICE |
| #QS-125WBKIT#1 | Gun with 125cc nylon cup, regulator, 0.8mm, 1.2mm, 1.5mm NN setups, repair kit, strainers, service wrench. Requires 4 CFM | $289.00 | |
NEEDLE/NOZZLE/AIRCAP SETS
#QS-125/0.viii – 0.8mm NN set – $59.95
#QS-125/ane.0 – 1.0mm NN gear up – $59.95
#QS-125/1.2 – i.2mm NN set – $59.95
#QS-125/i.5 – i.5mm NN gear up – $59.95
SPARE/Actress CUPS
Note: Please allow us know which version (male thread or female thread) you lot accept on your QS-125WB when ordering a new or spare cup.
#QS-125NYC – 125ml nylon cup – $25.00
#QS-125/200ALC – 200cc aluminum cup – $28.00
#QS-125/200SS – 200cc stainless cup – $35.00
#QS-125/400ALC – 400cc aluminum cup – $28.00
#QS-125/600NYC – 600cc nylon loving cup – $30.00
#QS-125/600ALC – 600cc aluminum loving cup – $32.00
#QS-125/MINI-Start – 3m PPS Mini-Cup "starter set".
Includes 1 mini 6 oz cup #16115, 10 #16114 lids and liners, &PPS adapter – $59.00
SPARE PARTS
#QS-125/RK – Rebuild Kit (springs, seals, washers) – $25.00
AM Series SMARTPAK LVLP GUNS
New! AM-5008 "SmartPak" – This package contains all the nozzles required to spray the most popular waterbased and solvent based finishes and paints and it works with small compressors. The AM-5008S is the setup for all stains, sealers and clears. Also included are rebuild/service kits, mini-regulator and cleaning brushes. What a great deal this package is if y'all don't know what nozzles to get for your new gun. Gun incorporates stainless steel in the fluid passages, threaded connector to the loving cup, and the female connector in the nylon cup. This upgrade by our mill insures proper operation with waterborne finishes and catalyzed solvent products.
2 YEAR WARRANTY
Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Cups: 600cc (other sizes available)
Working Pressure : 29 psi (at gun inlet)
Air Consumption: 6 cfm
Needle/nozzle/air cap: included in kit, 1.0mm, one.3mm, 1.8mm
| MODEL # | DESCRIPTION | Buy At present | PRICE |
| AM-5008/Due south | Gun with 600cc cup, i.0mm, one.3mm, i.5mm NN setups, repair kit, strainers, service wrench | SHIPS FREE! | $325.00 |
| QS-ADDPPS | Add PPS starter kit – includes medium cup, 10 lids and liners, 3 caps & #ii PPS adapter. | SHIPS Gratis! | $65.00 |
ACCESSORIES & REPLACEMENT PARTS
#HW-SS-3G – 3 pack replacement stainless steel strainers – $7.50
#AM-5008/RK – rebuild kit (springs, seals, washers) – $25.00
#AM-5008/125NYC – 125cc nylon cup – $25.00
#AM-5008/200ALC – 200cc aluminum cup – $30.00
#AM-5008/400ALC – 400cc aluminum loving cup – $35.00
#AM-5008/600NYC – 600cc nylon cup – $39.99
#AM-5008/600ALC – 600cc aluminum cup – $39.99
#AM-5008/1000ALC – 1000cc aluminum cup – $45.00
REPLACEMENT NEEDLE/NOZZLE/AIRCAP SETS
#AM-5008/10 – 1.0mm NN kit for AM-5008 – $59.95
#AM-5008/xiii – 1.3mm NN kit for AM-5008 – $59.95
#AM-5008/fifteen – 1.5mm NN kit for AM-5008 – $59.95
#AM-5008/18 – i.8mm NN kit for AM-5008 – $59.95
#AM-5008/20 – ii.0mm NN kit for AM-5008 – $59.95
#AM-5008/25 – 2.5mm NN kit for AM-5008 – $59.95
Perfect for Luthiers!
AM-8008/5008 "SmartPak" – We almost called this package the "Not Sure Which Spray Gun To Get-Kit". This package contains both a small gravity detail gun and a full size gravity gun. Both are LVLP guns and will work with small-scale compressors. The 1.4mm setup in the large gun will handle clears and the small gravity gun with 1.0mm is perfect for stains, sealers and near clear finishes (some may require thinning). The 2 cups have adapters so y'all can use both cup sizes with either gun, and included are rebuild/service kits, mini-regulator and cleaning brushes. What a great bargain this package is if you don't know whether to get a full size or detail gun. Both guns incorporate stainless steel in the fluid passages, threaded connector to the cup, and the female connector in the nylon cup. This upgrade by our manufacturing plant insures proper performance with waterborne finishes and catalyzed solvent products.
Body: forged aluminum
Nozzle/needle: stainless steel
Air cap: nickled brass
Gaskets: Teflon
Cups: 125cc and 600cc
Working Pressure : 29 psi (at gun inlet)
Air Consumption: iii cfm (detail gun) 5.5 cfm (large gun)
Needle/nozzle/air cap: ane.0mm (detail gun), i.4mm (large gun)
AM-8008/5008 – Ii Gun kit (shown above), – $375.00
ACCESSORIES & REPLACEMENT PARTS
#HW-SS-3G – 3 pack replacement stainless steel strainers – $vii.50
#AM-5008/125NYC – 125cc nylon cup – $25.00
#AM-5008/200ALC – 200cc aluminum cup – $28.00
#AM-5008/400ALC – 400cc aluminum cup – $28.00
#AM-5008/600NYC – 600cc nylon cup – $30.00
#AM-5008/600ALC – 600cc aluminum cup – $32.00
#AM-5008/1000ALC – 1000cc aluminum cup – $35.00
REPLACEMENT NEEDLE/NOZZLE/AIRCAP SETS
#AM-5008/10 – 1.0mm NN kit for AM-5008 – $54.95
#AM-5008/13 – 1.3mm NN kit for AM-5008 – $54.95
#AM-5008/xv – 1.5mm NN kit for AM-5008 – $54.95
#AM-5008/xviii – 1.8mm NN kit for AM-5008 – $54.95
#AM-5008/20 – 2.0mm NN kit for AM-5008 – $54.95
#AM-5008/25 – 2.5mm NN kit for AM-5008 – $54.95
#AM-8008/0.8 – 0.8mm NN gear up for AM-8008 – $45.00
#AM-8008/1.2 – ane.2mm NN set for AM-8008 – $45.00
#AM-8008/1.5 – i.5mm NN set for AM-8008 – $45.00
Source: https://homesteadfinishingproducts.com/qualspray-spray-guns-for-guitar-making/
Posted by: gilmandulaying78.blogspot.com
0 Response to "Is There A Spray On Guitar Case Cover Repair?"
Post a Comment